欢迎光临济南大黄蜂工程机械有限公司

热门关键词:

  • 移动碎石机租赁
  • 圆锥碎石机租赁
  • 反击破碎机租赁
当前位置: 首页 - 新闻中心 >
山东大黄蜂工程机械有限公司
电    话:18366127778
地    址:济南市槐荫区经一路273号群盛华城2号楼1-404
网    址:http://www.dhfjx.cn
新闻中心
更好的提升圆锥碎石机效率的措施都有哪些?
网址:http://www.dhfjx.cn    发布时间:2020-03-12
  圆锥破碎机可以安全生产,是每个消费者更关心的问题,因为机器的安全生产不仅改善生产的前景,但也会减少机器的失败。对此,本文总结了三点,以下是如何使圆锥破碎机安全生产。
  Cone crusher can work safely, which is the most concerned problem of every consumer, because the safe production of the machine not only improves the prospect of production, but also reduces the failure of the machine. In this regard, this paper summarizes three points, the following is how to make the cone crusher safe production.
  1. 生产前检查
  1. Pre production inspection
  1. 检查破碎室是否有堆积物料。在启动圆锥破碎机时,首先要确保破碎腔内的物料已被清空。
  1. Check whether there is any accumulated material in the crushing chamber. When starting the cone crusher, first make sure that the material in the crushing chamber has been emptied.
  2,检查零部件是否损坏,如:动态锥,球面轴承、主轴、板和厚板磨损部件,如主轴,如检查机器的主轴严重受损,圆锥破碎机运行时,过载的主轴,使用很长一段时间,将导致圆锥破碎机轴断裂,和其他部件损坏。
移动碎石机租赁
  2. Check whether the parts are damaged, such as: dynamic cone, spherical bearing, main shaft, plate and heavy plate wear parts, such as main shaft, such as the main shaft of the inspection machine is seriously damaged, when the cone crusher is running, the overloaded main shaft will be used for a long time, which will lead to the fracture of the cone crusher shaft and other parts damage.
  3、检查润滑油,为了使圆锥破碎函数更安全生产,应检查机器的润滑油,如油是否足够,油温是否过低,如检查油温过低,必须首先启动加热器加热油、回水管温度必须达到至少17℃启动破碎机。新圆锥破碎机启动前,回管温度应至少达到30℃,空载运行2h。
  3. Check the lubricating oil. In order to make the cone crushing function more safe in production, check the lubricating oil of the machine. If the oil is enough and the oil temperature is too low, first start the heater to heat the oil and the return pipe temperature must reach at least 17 ℃ to start the crusher. Before the new cone crusher is started for the first time, the return pipe temperature shall be at least 30 ℃, and the crusher shall be operated for 2h without load.
  二、正确的喂养方式
  2、 The right way to feed
  1. 物料必须由分配板均匀输入,不能直接进入破碎室,输入物料应低于砂浆墙的标高;同时,还要注意材料的尺寸。圆锥破碎机的大进料尺寸小于进料尺寸的85%(一般为50mm~300mm)。
  1. The materials must be evenly input from the distribution board, not directly into the crushing chamber, and the input materials shall be lower than the elevation of the mortar wall; at the same time, pay attention to the size of the materials. The large feed size of cone crusher is less than 85% of the feed size (generally 50 mm ~ 300 mm).
  2、不能出现全现象,使机器不仅不能安全生产,而且还会导致圆锥破碎机的失效,如破碎零件动态圆锥损坏、机器振动等问题。
  2. The whole phenomenon can not appear, which makes the machine not only unsafe in production, but also leads to the failure of cone crusher, such as dynamic cone damage of broken parts, machine vibration and other problems.
  3。停止生产时的注意事项
  3. Precautions when stopping production
  在圆锥破碎机生产工作结束时,应先停止进料,并让破碎的物料进入破碎室,完全排出后,在圆锥破碎机停止;停机后应全面检查机器,并立即处理需要维修的零件。
  At the end of the production of cone crusher, the feeding shall be stopped first, and the crushed materials shall be allowed to enter the crushing chamber. After being completely discharged, the cone crusher shall be stopped; after shutdown, the machine shall be comprehensively inspected and the parts requiring maintenance shall be handled immediately.
  以上就是移动碎石机租赁对圆锥碎石机效率更好的提升的措施的详细介绍,想要了解更多请点击官网http://www.dhfjx.cn
  The above is a detailed introduction to the measures for improving the efficiency of cone crusher by mobile crusher leasing. For more information, please click http://www.dhfjx.cn
上一条:如何保证反击破碎机运作效率?        下一条:反击破碎机使用受哪些外部因素的...

创新驱动发展,科技引领未来,诚信铸就品牌

地址:济南市槐荫区经一路273号群盛华城2号楼1-404  电话:18366127778

山东大黄蜂工程机械有限公司      流量分析: