欢迎光临济南大黄蜂工程机械有限公司

热门关键词:

  • 移动碎石机租赁
  • 圆锥碎石机租赁
  • 反击破碎机租赁
当前位置: 首页 - 新闻中心 >
山东大黄蜂工程机械有限公司
电    话:18366127778
地    址:济南市槐荫区经一路273号群盛华城2号楼1-404
网    址:http://www.dhfjx.cn
新闻中心
圆锥碎石机卡机的解决措施都有哪些?
网址:http://www.dhfjx.cn    发布时间:2020-02-20
圆锥碎石机由于某些设备的突然故障而卡死,严重影响了生产,降低了设备和部件的使用寿命,让我们来看看圆锥碎石机卡死的三种现象。
The cone crusher is stuck due to the sudden failure of some equipment, which seriously affects the production and reduces the service life of the equipment and components. Let's take a look at three phenomena of the cone crusher stuck.
一是动锥和调节套卡住
First, the moving cone and the adjusting sleeve are stuck
1. 当圆锥碎石机带负荷运行时,由于液压站内压力损失导致锁紧失效,调节套筒随圆锥旋转。如果岗位人员没有及时发现和处理,就会造成调整设置卡死现象,从而导致圆锥碎石机停机。
1. When the cone crusher is running with load, the locking failure is caused by the pressure loss in the hydraulic station, and the adjusting sleeve rotates with the cone. If the post personnel do not find and deal with it in time, the adjustment setting will be blocked, which will lead to the shutdown of the cone crusher.
2. 调整套死的原因还可能是螺纹润滑不良、调整帽或防尘罩的密封磨损、调整套和支撑套的螺纹磨损、或调整套断后锥体过载等。
2. The reasons for the dead adjustment sleeve may also be the poor thread lubrication, the seal wear of the adjustment cap or dust cover, the thread wear of the adjustment sleeve and the support sleeve, or the overload of the cone after the adjustment sleeve is broken, etc.
移动碎石机租赁
二、堵料卡死
2、 Blocking blocked
1、圆锥碎石机进料过多,或进料性能不符合要求,导致圆锥碎石机堵塞,会使碎石机工作电流过大,自动回路保护并停止机器,甚至可能出现圆锥碎石机卡住而被迫停止的状态。
1. Too much material is fed into the cone crusher, or the feeding performance does not meet the requirements, resulting in the blockage of the cone crusher, which will cause the working current of the crusher to be too large, automatic circuit protection and stop the machine, and even the cone crusher may be stuck and forced to stop.
2. 当铁或其他非破碎物体进入圆锥碎石机破碎腔时,也会造成碎石机堵塞甚至设备卡住的现象。
2. When iron or other non broken objects enter into the crushing chamber of the cone crusher, it will also cause the crusher to be blocked or even the equipment to be stuck.
三、主轴断裂卡住
3、 Spindle broken and stuck
1. 圆锥碎石机使用不当是主轴断裂的主要原因之一。例如,为了达到所需的出料细度,出料口不断收紧。
1. Improper use of the cone crusher is one of the main reasons for the fracture of the main shaft. For example, in order to achieve the required discharge fineness, the discharge port is constantly tightened.
2. 另一方面,当断锥长期处于过载运行状态时,虽有过载保护装置,但仍不能完全避免对设备的损坏,主轴容易断裂,造成装置卡死。
2. On the other hand, when the broken cone is in the state of overload operation for a long time, although there is an overload protection device, it can not completely avoid the damage to the equipment. The main shaft is easy to break, causing the device to be stuck.
以上就是移动碎石机租赁对圆锥碎石机卡机的解决措施的详细介绍,想要了解更多请点击官网http://www.dhfjx.cn
The above is the detailed introduction of the solution to the cone crusher jamming by the mobile crusher leasing. For more information, please click http://www.dhfjx.cn

上一条:移动碎石机租是否可以成为近几年...        下一条:移动碎石机启动时的注意事项?

创新驱动发展,科技引领未来,诚信铸就品牌

地址:济南市槐荫区经一路273号群盛华城2号楼1-404  电话:18366127778

山东大黄蜂工程机械有限公司      流量分析: