欢迎光临济南大黄蜂工程机械有限公司

热门关键词:

  • 移动碎石机租赁
  • 圆锥碎石机租赁
  • 反击破碎机租赁
当前位置: 首页 - 新闻中心 >
山东大黄蜂工程机械有限公司
电    话:18366127778
地    址:济南市槐荫区经一路273号群盛华城2号楼1-404
网    址:http://www.dhfjx.cn
新闻中心
圆锥碎石机配件不可忽视的装置流程?
网址:http://www.dhfjx.cn    发布时间:2020-01-14
液压装置可用于拆卸主滑轮。
  The hydraulic unit can be used to remove the main pulley.
  磁电机零件的安装
  Installation of magneto parts
  1)三瓶偏心块的部分,上下偏心块和轴套上的一对应该键和键槽的三套轴袖子,不同位置的键槽可以更换轴套的延长使用寿命。
  1) The part of the eccentric block of three bottles, the upper and lower eccentric blocks and a pair of shaft sleeves corresponding to the key and the keyway. The keyway at different positions can replace the shaft sleeve to extend the service life.
  2)三个偏心块的扇形部分外侧有多个键槽。偏心块是通过上下偏心块的力用长键固定的。中间偏心块与上下偏心块的相对位置可根据不同破碎力的需要进行调整。
  2) There are multiple keyways on the outside of the sector part of the three eccentric blocks. The center eccentric block is fixed with a long key by the force of the upper and lower eccentric blocks. The relative position of the middle eccentric block and the upper and lower eccentric blocks can be adjusted according to the needs of different crushing forces.
  3)偏心块上下料时,可用小角楔铁稍微加大偏心块开口,方便上下料。
  3) When the eccentric block is loaded and unloaded, the small angle wedge iron can be used to slightly increase the opening of the eccentric block to facilitate loading and unloading.
  4)用高强度钢结构螺栓锁紧偏心块,将螺母沉到开槽侧。其他高强度螺栓因条件限制只能现场使用时,不得将沉头螺栓旋转90°;否则,薄铁板应对称焊接在螺母的两侧,使螺母能被开槽锁紧。
移动碎石机租赁
  4) Lock the eccentric block with high-strength steel structural bolt, and sink the nut to the slotted side. When other high-strength bolts can only be used on site due to restrictions of conditions, the countersunk head bolt shall not be rotated 90 °; otherwise, the thin iron plate shall be welded symmetrically on both sides of the nut, so that the nut can be locked by slotting.
  5)拧紧螺母,使开口的两个平面平行,然后在施加预紧力时,用一米长的应力棒将螺母拧紧到一定角度。施加预紧力后,锁紧螺母。
  5) Tighten the nut so that the two planes of the opening are parallel, and then use a one meter long stress bar to tighten the nut to a certain angle when applying the preload. After the preload is applied, lock the nut.
  6)在偏心块附近安装两个锁定板。如果套筒的上表面与轴向键槽之间有间隙,则可在锁板下用薄铁板进行补偿。拧紧螺栓并锁紧。
  6) Install two locking plates near the eccentric. If there is a gap between the upper surface of the sleeve and the axial keyway, it can be compensated with a thin iron plate under the locking plate. Tighten the bolts and lock them.
  安装振动筛总成和移动锥架
  Install the shale shaker assembly and moving cone frame
  1)为了保证紧密接触均匀,辅助支撑球瓦应与锥支撑钢瓦刮在一起,保证每个25mm×25mm的球瓦外圈有10 ~ 15个接触点,内环有一定的环形间隙。
  1) In order to ensure even close contact, the auxiliary support ball bearing shall be scraped together with the tapered support steel bearing to ensure that each 25 mm × 25 mm ball bearing outer ring has 10 to 15 contact points, and the inner ring has a certain annular gap.
  2)躺地上的瓶子的支持移动锥,把法兰轴套,加载锥套扣,确保扣附着在轴套圆周键槽和陷入的锥套的步骤(见图2)。
  2) Lay the bottle on the ground to support the moving cone, put the flange shaft sleeve, load the taper sleeve buckle, and ensure that the buckle is attached to the circumferential keyway of the shaft sleeve and the sunk taper sleeve (see Fig. 2).
  图2法兰、锥套、卡环、轴套安装示意图
  Fig. 2 installation diagram of flange, cone sleeve, snap ring and shaft sleeve
  3)缓慢提起动锥支架,使励磁机略离地,依次、反复、对称地拧紧法兰上的8个螺栓,然后用铁丝将螺栓锁紧成两组。
  3) Slowly lift the moving cone bracket to make the exciter slightly off the ground, successively, repeatedly and symmetrically tighten 8 bolts on the flange, and then lock the bolts into two groups with iron wire.
  4)正确安装辅助支撑球瓦和激振器,有利于保证设备的可靠性。
  4) It is helpful to ensure the reliability of the equipment to install the auxiliary support ball and exciter correctly.
  活动锥的安装
  Installation of movable cone
  1)涂覆后清除主轴、球体、锥体上的保护油层。
  1) After coating, remove the protective oil layer on the spindle, ball and cone.
  2)在主轴表面涂一层干黄油,在球、锥体表面涂一层薄油。
  2) Apply a layer of dry grease on the surface of the main shaft and a thin layer of oil on the surface of the ball and cone.
  3)用薄塑料纸包裹主轴,防止污染。
  3) Wrap the spindle with thin plastic paper to prevent pollution.
  4)将锥铁架子,动锥板的外表面焊接两个对称环,安装电梯移动锥锥板,安装在一个小板,垫环和盖形螺母(左旋螺纹),然后使用一个特殊的锤击扳手拧紧盖形螺母,用厚薄规检查锥板和动锥之间的空间,和接近于零的差距和周围。
  4) Weld two symmetrical rings on the outer surface of the cone iron frame and the moving cone plate, install the elevator moving cone plate on a small plate, the backing ring and the cap nut (left-hand thread), then use a special hammer wrench to tighten the cap nut, use a feeler gauge to check the space between the cone plate and the moving cone, and the gap and surroundings close to zero.
  5)在大会期间,起重机移动锥帽螺母的一部分,移动的锥轴套筒瓶温柔和缓慢的部分,并使动锥球接触的稳定支持球面瓦动锥,以免移动锥舌环或花的外缘移动锥和破碎的密封环的支持。
  5) During the assembly, the crane moves a part of the cone cap nut, the moving cone shaft sleeve bottle gently and slowly, and makes the moving cone ball contact the stable support spherical tile moving cone, so as to avoid moving the outer edge of the cone tongue ring or flower moving the support of the cone and the broken sealing ring.
  调整环的安装
  Installation of adjusting ring
  1)调节环部件包括料斗、螺纹环、固定锥套等部件。安装质量也会影响设备运行的稳定性、压碎效果和固定锥套的使用寿命。
  1) Adjusting ring parts include hopper, threaded ring, fixed cone sleeve and other parts. The installation quality will also affect the stability of the equipment operation, crushing effect and the service life of the fixed cone sleeve.
  2)固定锥套与螺纹环通过锥面相互接触。安装时应放置固定的锥套,在其上应放置螺纹环,在螺纹环上应放置法兰。夹紧环应附在固定锥套的外颈环上。
  2) The fixed taper sleeve and the threaded ring contact each other through the taper surface. Fixed taper sleeve shall be placed during installation, threaded ring shall be placed on it, and flange shall be placed on threaded ring. The clamping ring shall be attached to the outer neck ring of the fixed taper sleeve.
  3)安装固定锥套后,可安装压铁、密封圈、料斗等部件。
  3) After installing the fixed cone sleeve, it is possible to install the iron pressing, sealing ring, hopper and other components.
  以上就是圆锥碎石机租赁配件的装置流程的详细介绍,想要了解更多请点击官网http://www.dhfjx.cn
  The above is a detailed introduction to the installation process of rental accessories of cone crusher. For more information, please click http://www.dhfjx.cn
上一条:反击式破碎技术特点都体现哪些方面?        下一条:移动碎石机为什么会成为破碎设备...

创新驱动发展,科技引领未来,诚信铸就品牌

地址:济南市槐荫区经一路273号群盛华城2号楼1-404  电话:18366127778

山东大黄蜂工程机械有限公司      流量分析: