欢迎光临济南大黄蜂工程机械有限公司

热门关键词:

  • 移动碎石机租赁
  • 圆锥碎石机租赁
  • 反击破碎机租赁
当前位置: 首页 - 新闻中心 >
山东大黄蜂工程机械有限公司
电    话:18366127778
地    址:济南市槐荫区经一路273号群盛华城2号楼1-404
网    址:http://www.dhfjx.cn
新闻中心
降低碎石机板锤消耗有什么好的办法?
网址:http://www.dhfjx.cn    发布时间:2019-08-30
碎石机板锤是与物料直接接触的,所以板锤的消耗一直过大,板锤的主要损坏形式是松脱和断裂,而不是正常的磨损。板锤的松脱和断裂,轻则打断螺栓和其它板锤,损坏转子体及反击架,重则打断转子体轴,撕裂转子体,而且板锤消耗量很大。针对此问题,移动碎石机租赁厂家在本文将介绍降低碎石机板锤消耗的应对措施。
The hammer of the crusher is in direct contact with the material, so the consumption of the hammer has been too large. The main damage form of the hammer is loosening and breaking, not normal wear and tear. The loosening and breaking of plate hammer can break bolts and other plate hammers lightly, damage the rotor body and counterattack frame, break the shaft of the rotor body heavily, tear the rotor body, and consume a lot of plate hammer. In order to solve this problem, the rental manufacturer of mobile gravel crusher will introduce the measures to reduce the consumption of slab hammer of gravel crusher in this paper.
1、尽量使用质量好的板锤
1. Make the best use of the board hammer with good quality.
针对板锤的质量问题,嵩源实业建议选用原碎石机制造厂的板锤,基本达到了质量要求。
In view of the quality problem of the plate hammer, Songyuan Industry suggested that the original stone crusher factory should be chosen as the plate hammer, which basically meets the quality requirements.
2、重新制作螺栓模具
2. Re-manufacture of Bolt Mould
使螺栓的椭圆头与板锤螺孔接触面能良好接触,同时,将螺栓螺纹牙的厚度控制在尺寸允差内,螺纹的收尾加工出卸荷槽,以防应力集中而断裂。
The elliptical head of the bolt can be in good contact with the contact surface of the hole of the plate hammer. At the same time, the thickness of the thread teeth of the bolt is controlled within the allowable size. The unloading groove is processed at the end of the thread to prevent stress concentration and fracture.
移动碎石机租赁
3、加强使用和维护管理
3. Strengthen the Management of Use and Maintenance
首先,板锤安装时,必须清除板锤螺栓孔及槽口的型砂及毛刺,使联接时贴合平实;其次,紧固板锤螺栓时,要边紧固边锤击椭圆头;再则,运行后约半小时要及时检查螺栓紧固情况,紧固后再将螺母与螺纹点焊以防松动。
First, when plate hammer is installed, the moulding sand and burrs of bolt holes and grooves of plate hammer must be cleared so as to make the connection fit smoothly; secondly, when fastening plate hammer bolts, the elliptical head should be hammered while fastening; thirdly, the bolt tightening situation should be checked in time about half an hour after operation, and then the nut and thread should be spot welded after tightening to prevent loosening.
4、喂料时物料要符合设备要求
4. Material should meet equipment requirements when feeding
操作人员在进行喂料前,首先要仔细阅读该设备的破碎范围,因为不同的碎石机破碎的物料硬度不同,物料在进行破碎腔前应事先做一下处理措施,减少物料的粘性和含水量。
Before feeding, the operator should first read the crushing range of the equipment carefully, because different crushers have different hardness of crushed materials, and materials should be treated beforehand before crushing chamber to reduce the viscous and moisture content of materials.
感谢您的阅读与观看,本文的精彩内容来自:移动碎石机租赁,我们会有更多的精彩内容继续为您呈现,详情请点击:http://www.dhfjx.cn
Thank you for your reading and watching. The wonderful content of this article comes from: mobile gravel rental, we will have more wonderful content to continue to show you. For more details, please click: http://www.dhfjx.cn.
上一条:反击破碎机的清洁工作有什么需要...        下一条:简单4大要点,轻松搞定破碎机的...

创新驱动发展,科技引领未来,诚信铸就品牌

地址:济南市槐荫区经一路273号群盛华城2号楼1-404  电话:18366127778

CopyRight © 2018. 山东大黄蜂工程机械有限公司 All Rights Reserved.   技术支持: 济南诺商  
备案号:鲁ICP备17031054号-1  流量分析: