欢迎光临济南大黄蜂工程机械有限公司

热门关键词:

  • 移动碎石机租赁
  • 圆锥碎石机租赁
  • 反击破碎机租赁
当前位置: 首页 - 新闻中心 >
山东大黄蜂工程机械有限公司
电    话:18366127778
地    址:济南市槐荫区经一路273号群盛华城2号楼1-404
网    址:http://www.dhfjx.cn
新闻中心
破碎机齿板更换步骤及使用规范
网址:http://www.dhfjx.cn    发布时间:2019-06-19
破碎机齿板是运用于破碎机中的的主要部件,是直接与矿石接触的部分,市面上普通的破碎机齿板通常使用寿命都很短,因为破碎机齿板达到一定的磨损程度后就必须进行更换,济南移动式碎石机租赁小编就为您总结了以下几点:
Crusher tooth plate is the main component used in crusher, which is directly in contact with ore. The service life of ordinary crusher tooth plate on the market is usually very short, because the crusher tooth plate must be replaced after reaching a certain degree of wear and tear. Jinan Mobile Crusher Rental Chapter summarizes the following points for you:
1.破碎机齿板更换前需要注意的事项:
1. Matters needing attention before replacing the gear plate of crusher:
1.事先确定破碎机齿板的技术方案。
1. Determine the technical scheme of crusher tooth plate beforehand.
2.提前准备拆除和安装工具(扳手,电动工具等),设备保护要灵敏、齐全、可靠。
2. Prepare to dismantle and install tools (wrenches, electric tools, etc.) in advance. Equipment protection should be sensitive, complete and reliable.
3.提前清理破碎机腔内的杂物,方便检修。
3. Clean up the debris in the crusher chamber in advance for easy maintenance.
4.断开电源,关停设备。
4. Disconnect the power supply and shut down the equipment.
移动碎石机齿板
破碎机齿板更换步骤:
Crusher tooth plate replacement steps:
1.将破碎机用起重装置移动至检修位置,方便拆装破碎机内的齿板。
1. Move the crusher to the overhaul position with the lifting device to facilitate the disassembly and assembly of the teeth plate in the crusher.
2.对两端齿板更换,采取“先更换完上面的一块齿板后,将破碎轴旋转一定角度,再更换下一块”的步骤,重复此步骤。要注意的是更换时施力的不平衡会引起轴的突然转动。可以用木楔阻止轴的转动,然后更换。
2. To replace the two ends of the plate, take the steps of "first replace the top plate, rotate the crushing shaft at a certain angle, and then replace the next plate", repeat this step. It is important to note that the unbalanced force applied during the replacement will cause a sudden rotation of the shaft. Wedges can be used to stop the rotation of the shaft, and then replaced.
3.新齿板安装前,安放齿板的位置必须保证清洁,特别是齿板与齿板螺栓接触面的表面。
3. Before installing the new plate, the position of the plate must be kept clean, especially the surface of the contact surface between the plate and the bolt of the plate.
4.安装新齿板时,需将齿板调节至适当的配合位置,并用锤子将其敲入固定位置。
4. When installing the new gear plate, it is necessary to adjust the gear plate to the appropriate matching position and hammer it into the fixed position.
5.固定齿板螺栓,将齿板螺栓放入齿板上的螺栓孔,然后旋转90度,将卡块放入螺栓孔中,紧贴螺栓以防螺栓转动脱落。
5. Fixed the plate bolt, put the plate bolt into the bolt hole on the plate, then rotate 90 degrees, put the clamp into the bolt hole, close to the bolt to prevent the bolt from rotating and falling off.
6.将垫片倒角朝下套放在螺栓上,然后拧紧螺母。重复此步骤安装其他齿板螺栓。
6. Put the gasket chamfer downward sleeve on the bolt and tighten the nut. Repeat this step to install other plate bolts.
7.护板归位防护罩归位
7. Relocation of protective shield
这就是今天由济南移动式碎石机租赁小编给大家介绍的纯干货的内容了,相信今天的内容能给大家带来一定的帮助,如果您对文章的内容还有不明白的地方,欢迎大家点击我们的官方网站留言讨论:http://www.dhfjx.cn
This is the content of pure dry goods introduced to you by Jinan Mobile Stone Crusher Leasing Editor today. I believe that today's content can bring you some help. If you still don't understand the content of this article, you are welcome to click on our official website to discuss: http://www.dhfjx.cn.
上一条:辊式破碎机辊皮磨损的5大主要因素!        下一条:反击式破碎机有哪些型号?多少钱...

创新驱动发展,科技引领未来,诚信铸就品牌

地址:济南市槐荫区经一路273号群盛华城2号楼1-404  电话:18366127778

CopyRight © 2018. 山东大黄蜂工程机械有限公司 All Rights Reserved.   技术支持: 济南诺商  
备案号:鲁ICP备17031054号-1  流量分析: